- Longueur hors tout : 29.2 ft / 8898 mm
- Largeur hors pneus : 8.47 ft / 2581 mm
- Empattement : 20.1 ft / 6126 mm
- Rear Ground Clearance : 1.13 ft / 344 mm
Dimensions et poids publiés
Caterpillar 140M2
La Caterpillar 140M2 associe le moteur C9.3 ACERT VHP (223 ch) à une masse d'environ 19,8 t.
01Dimensions et poids publiés
Référence des dimensions
Repère de mesure — non à l'échelle
01Référence des dimensionsLongueur × largeur × hauteur
02Poids d'exploitation standard - total37911 lb17196.2 kg
03Valeurs publiées sélectionnées202
Les niveleuses servent couramment à profiler, à niveler et à entretenir les routes, les plateformes et les surfaces de drainage. Les lignes publiées pour Caterpillar 140M2 comprennent une largeur de versoir publiée de 12 ft / 3657.6 mm, un poids opérationnel publié de 37911 lb / 17196.2 kg, le champ publié « Overall Length » de 29.2 ft / 8898 mm. Ces valeurs décrivent la configuration publiée; vérifiez la configuration, les accessoires et les documents de la machine précise.
- Comparez le champ publié « Longueur hors tout » (29.2 ft / 8898 mm) à la configuration et aux documents de la machine précise; les options et l'état peuvent différer.
- Comparez le champ publié « Largeur hors pneus » (8.47 ft / 2581 mm) à la configuration et aux documents de la machine précise; les options et l'état peuvent différer.
- Comparez le champ publié « Empattement » (20.1 ft / 6126 mm) à la configuration et aux documents de la machine précise; les options et l'état peuvent différer.
02Spécifications
Valeurs publiées, regroupées clairement.
Les spécifications et mesures publiées sont organisées par section pour faciliter la consultation.
Dimensions
Longueur hors tout29.2 ft8898 mm
Largeur hors pneus8.47 ft2581 mm
Empattement20.1 ft6126 mm
Rear Ground Clearance1.13 ft344 mm
Tandem Axle Wheelbase5 ft1523 mm
Front Ground Clearance1.97 ft600 mm
Blade Base8.39 ft2557 mm
Hauteur au sommet de la cabine Isomount10.79 ft3287 mm
Défonceuse
Pry-Out Force27655 lb12544.1 kg
Ripping Depth - Maximum16.8 in426.8 mm
Ripper Shank Holders55
Penetration Force20693 lb9386.2 kg
Machine Length Increase, Beam Raised40.6 in1031.3 mm
Ripper Shank Holder Spacing21 in533.4 mm
Moteur
Nombre de cylindres66
Marque du moteur22362236
Modèle du moteurC9.3 ACERT VHPC9.3 ACERT VHP
Puissance mesurée à2100 rpm2100 rpm
Couple mesuré à2100 rpm2100 rpm
Net Power Gears 7-8223 hp166.3 kw
Net Torque Gears 7-8920 lb ft1247.4 Nm
Cylindrée567.5 cu in9.3 L
Alésage4.5 in114.3 mm
Course5.9 in149.9 mm
EmissionsU.S. Tier 4 Interim/EU Stage IIIBU.S. Tier 4 Interim/EU Stage IIIB
Derating Altitude10000 ft3048 m
Maximum Torque920 lb ft1247.4 Nm
Base Power (1st Gear) - Net193 hp144 kw
Standard Capability109 degrees109 degrees
Speed At Rated Power2,100 rpm2,100 rpm
High - Ambient Capability122 degrees122 degrees
Base Power (1st Gear) - Net - Metric196 hp146.2 kw
High Ambient - Fan Speed - Maximum1,550 rpm1,550 rpm
High Ambient - Fan Speed - Standard1,400 rpm1,400 rpm
High Ambient - Fan Speed - Minimum500 rpm500 rpm
Vhp Plus Range - Net144-181 kW (193-243 hp)144-181 kW (193-243 hp)
Vhp Plus Range - Net - Metric144-181 kW (196-246 hp)144-181 kW (196-246 hp)
Vhp Plus - Gear 1f, Net193 hp144 kw
Vhp Plus - Gear 2f, Net202 hp150.7 kw
Vhp Plus - Gear 3f, Net213 hp158.9 kw
Vhp Plus - Gear 4f, Net223 hp166.3 kw
Vhp Plus - Gear 5f, Net228 hp170.1 kw
Vhp Plus - Gear 6f, Net233 hp173.8 kw
Vhp Plus - Gear 7f, Net238 hp177.5 kw
Vhp Plus - Gear 8f, Net243 hp181.3 kw
Châssis
Front Frame Structure - Height1.1 ft320.1 mm
Front Frame Structure - Width0.9 ft254 mm
Circle - Diameter60.2 in1529.1 mm
Drawbar - Height6 in152.4 mm
Front Axle - Height To Center23.6 in599.5 mm
Circle - Blade Beam Thickness1.6 in40.7 mm
Front Axle - Total Oscillation Per Side32 degrees32 degrees
Drawbar - Thickness0.5 in12.7 mm
Drawbar - Width3 in76.2 mm
Front-Top/Bottom Plate - Width12 in304.8 mm
Front-Top/Bottom Plate - Thickness0.9 in22.1 mm
Front Axle - Wheel Lean - Left/Right18 degrees18 degrees
Exploitation
Std Operation Weight - Front Axle9284 lb4211.2 kg
Std Operation Weight - Rear Axle28627 lb12985 kg
Capacité du circuit hydraulique26.5 gal100 L
Poids d'exploitation standard - total37911 lb17196.2 kg
Max Operation Weight - Front Axle13343 lb6052.3 kg
Max Operation Weight - Rear Axle36444 lb16530.8 kg
Capacité du circuit d'huile8 gal30 L
Max Operation Weight - Total49787 lb22583.1 kg
Capacité de carburant109.9 gal416 L
Capacité du système de refroidissement14.8 gal56 L
Capacité de fluide de transmission17.2 gal65 L
Circle Gearbox Fluid Capacity1.9 gal7 L
Tandem Case Fluid Capacity (Each)17 gal64 L
Chaîne cinématique
Brakes - ParkingMultiple Oil DiscMultiple Oil Disc
Brakes - ServiceMultiple Oil DiscMultiple Oil Disc
TransmissionDirect Drive, PowershiftDirect Drive, Powershift
Forward/Reverse Gears8 Fwd/6 Rev8 Fwd/6 Rev
Brakes - SecondaryDual CircuitDual Circuit
Brakes - Service - Surface Area3565 in22.3 m2
Direction
Angle d'articulation20 degrees20 degrees
Rayon de braquage25.5 ft7.8 m
Transmission
Type de transmissionDirect Drive, PowershiftDirect Drive, Powershift
Nombre de rapports - avant88
Nombre de rapports - arrière66
Vitesse maximale - marche avant29 mph46.7 km/h
Vitesse maximale - marche arrière22.9 mph36.9 km/h
Essieu avant
Wheel Lean18 degrees18 degrees
Oscillation - Total32 degrees32 degrees
Garde au sol2 ft600 mm
Poids
Operating Weight - Typically Equipped43686 lb19815.7 kg
Gross Vehicle Weight - Base - Total37916 lb17198.5 kg
Gross Vehicle Weight - Maximum - Total54869 lb24888.2 kg
Operating Weight - Typically Equipped - Total43686 lb19815.7 kg
Gross Vehicle Weight - Base - Rear Axle28381 lb12873.5 kg
Operating Weight - Typically Equipped - Front Axle12483 lb5662.2 kg
Operating Weight - Typically Equipped - Rear Axle31203 lb14153.5 kg
Gross Vehicle Weight - Base - Front Axle9534 lb4324.6 kg
Gross Vehicle Weight - Maximum - Front Axle17009 lb7715.2 kg
Gross Vehicle Weight - Maximum - Rear Axle37860 lb17173.1 kg
Système hydraulique
Standby Pressure609 psi609 psi
Maximum System Pressure3500 psi3500 psi
Type de pompeVariable PistonVariable Piston
Débit de la pompe55.7 gal/min210.9 L/min
Pression de la soupape de décharge3500 psi24131.7 kPa
Circuit TypeParallelParallel
Pump Output55.7 gal/min55.7 gal/min
Reservoir Tank Capacity15.9 gal60 L
Lame niveleuse
Largeur de la lame12 ft3657.6 mm
Hauteur de la lame24 in609.6 mm
Moldboard Thickness0.9 in22 mm
Max Depth Of Cut28.2 in715 mm
Side Shift Left20.1 in510 mm
Side Shift Right26 in660 mm
Blade Pull At Max Weight20044 lb9091.9 kg
Blade Down Pressure22884 lb10380.1 kg
Blade Width12 ft3.7 m
Arc Radius16.3 in414.1 mm
Throat Clearance6.5 in165.1 mm
Cutting Edge Width6 in152.4 mm
Cutting Edge Thickness0.6 in15.3 mm
End Bit - Width6 in152.4 mm
End Bit - Thickness0.6 in15.3 mm
Moldboard - Height24 in609.6 mm
Moldboard - Thickness0.9 in22.1 mm
Blade Pull - Maximum Gvw34072 lb15454.9 kg
Blade Pull - Base Gvw25765 lb11686.9 kg
Blade Down Pressure - Base Gvw16365 lb7423.1 kg
Blade Down Pressure - Maximum Gvw29196 lb13243.1 kg
Cercle
Diameter60.3 in1530 mm
Rotation360 degrees360 degrees
Shift Left27.4 in695 mm
Shift Right28.7 in728 mm
Max Reach Outside Tires - Left70.5 in1790 mm
Max Reach Outside Tires - Right77.9 in1978 mm
Max Lift Above Ground18.9 in480 mm
Blade Tip Angle - Front40 degrees40 degrees
Blade Tip Angle - Rear5 degrees5 degrees
Spécifications d'exploitation
Top Speed - Forward29 mph46.7 km/h
Top Speed - Reverse22.9 mph36.9 km/h
Turning Radius - Outside Front Tires25 ft7.6 m
Steering Range - Left/Right47.5 degrees47.5 degrees
Articulation Angle - Left/Right20 degrees20 degrees
Forward - 8th29 mph46.7 km/h
Forward - 7th19.9 mph32.1 km/h
Forward - 6th14.5 mph23.4 km/h
Forward - 5th10.6 mph17.1 km/h
Forward - 4th6.9 mph11.2 km/h
Forward - 3rd5 mph8.1 km/h
Forward - 2nd3.4 mph5.5 km/h
Forward - 1st2.5 mph4.1 km/h
Reverse - 6th22.9 mph36.9 km/h
Reverse - 5th15.7 mph25.3 km/h
Reverse - 4th8.4 mph13.6 km/h
Reverse - 3rd5.4 mph8.7 km/h
Reverse - 2nd3.7 mph6 km/h
Reverse - 1st2 mph3.3 km/h
Équipement de série
BrakesISO 3450, ISO 10265ISO 3450, ISO 10265
Rops/FopsISO 3471/ISO 3499ISO 3471/ISO 3499
SoundISO 6394; ISO 6395ISO 6394; ISO 6395
SteeringISO 5010ISO 5010
Remplissage d'entretien
Système de refroidissement14.8 gal56.1 L
Hydraulic System - Total26.4 gal100 L
Huile moteur7.9 gal30 L
Hydraulic System - Tank16.9 gal64 L
Tandem Housing - Each16.9 gal64 L
Circle Drive Housing1.8 gal6.9 L
Front Wheel Spindle Bearing Housing0.2 gal0.5 L
Capacité de carburant110 gal416.4 L
Transmission - Differential - Final Drives17.2 gal65.2 L
Blade Range
Circle Centershift - Right28.7 in729 mm
Circle Centershift - Left27.4 in696 mm
Moldboard Sideshift - Right26 in660.4 mm
Moldboard Sideshift - Left20.1 in510.6 mm
Blade Tip Range - Forward40 degrees40 degrees
Blade Tip Range - Backward5 degrees5 degrees
Maximum Shoulder Reach Outside Of Tires - Right77.9 in1977.9 mm
Maximum Shoulder Reach Outside Of Tires - Left70.5 in1790.7 mm
Maximum Lift Above Ground18.9 in480.1 mm
Maximum Depth Of Cut28.1 in713.8 mm
Maximum Blade Position Angle90 degrees90 degrees
Scarifier
Front, V-Type - Working Width47.4 in1204 mm
Rear - Scarifier Shank Holders99
Mid, V-Type - Scarifier Shank Holders1111
Front, V-Type, 5 Or 11 Tooth - Working Width40.6 in1031.3 mm
Front, V-Type, 5 Or 11 Tooth - Scarifying Depth, Maximum18.4 in467.4 mm
Front, V-Type, 5 Or 11 Tooth - Scarifier Shank Holders5/115/11
Front, V-Type, 5 Or 11 Tooth - Scarifier Shank Holder Spacing4.6 in116.9 mm
Mid, V-Type - Working Width46.6 in1183.7 mm
Mid, V-Type - Scarifying Depth, Maximum11.5 in292.1 mm
Mid, V-Type - Scarifier Shank Holder Spacing4.6 in116.9 mm
Rear - Working Width84 in2133.6 mm
Rear - Scarifying Depth, Maximum16.8 in426.8 mm
Rear - Scarifier Shank Holder Spacing10.5 in266.7 mm
Front, V-Type - Scarifying Depth, Maximum40.6 in1031.3 mm
Front, V-Type - Scarifier Shank Holders5/115/11
Front, V-Type - Scarifier Shank Holder Spacing18.4 in467.4 mm
Rear - Ripping Depth, Maximum16.8 in426.8 mm
Tandems
Hauteur19.9 in505.5 mm
Largeur8.3 in210.9 mm
Sidewall Thickness - Inner0.7 in16.1 mm
Sidewall Thickness - Outer0.8 in18.1 mm
Drive Chain Pitch2 in50.8 mm
Wheel Axle Spacing60 in1522.8 mm
Tandem Oscillation - Front Up15 degrees15 degrees
Tandem Oscillation - Front Down25 degrees25 degrees
Besoin de la machine, pas seulement des chiffres?
Trouvez-en une, évaluez-la ou publiez votre demande.
Spécifications publiées par le fabricant.