- Overall Length: 45.61 ft / 13900 mm
- Overall Height: 26.25 ft / 8000 mm
- Wheelbase: 2.19 ft / 665 mm
- Turning Radius: 42.33 ft / 12900 mm
Published dimensions and weight
Komatsu 9.80E-02
The Komatsu 9.80E-02 pairs the SSDA18V170 engine (3500.1 hp) with an operating weight near 41.7 t.
01Published dimensions and weight
Dimensions reference
Representative category illustration; exact model may differ.Measurement reference — not to scale
01Dimensions referenceLength × width × height
02Weight92001.2 lb41731 kg
03Selected published values66
Rigid rock trucks are commonly used to haul rock and bulk material on mines, quarries and large earthmoving sites. Published rows for Komatsu 9.80E-02 include published payload of 814407.4 lb / 369409 kg, the published “Overall Length” field of 45.61 ft / 13900 mm, the published “Overall Height” field of 26.25 ft / 8000 mm. These values describe the published configuration; verify the specific machine's configuration, attachments and records.
- Compare the published “Overall Length” field (45.61 ft / 13900 mm) with the specific machine's configuration and records; options and condition can differ.
- Compare the published “Overall Height” field (26.25 ft / 8000 mm) with the specific machine's configuration and records; options and condition can differ.
- Compare the published “Wheelbase” field (2.19 ft / 665 mm) with the specific machine's configuration and records; options and condition can differ.
02Specifications
Published values, clearly grouped.
Published specifications and measurements are organized by section for quick reference.
Dimensions
Overall Length45.61 ft13900 mm
Overall Height26.25 ft8000 mm
Wheelbase2.19 ft665 mm
Turning Radius42.33 ft12900 mm
Width Over Tires-Front26.19 ft7980 mm
Width Over Tires-Rear29.79 ft9080 mm
Electric Drive
Ratio35.02:135.02:1
AlternatorGTA -39GTA -39
ControlAC Torque Control SystemAC Torque Control System
Motorised WheelsGDY108-C Induction Traction MotorsGDY108-C Induction Traction Motors
Maximum Speed (Km/H)6161
Dual Fan Main Blower340 m3/min 12,000 cfm340 m3/min 12,000 cfm
Electrical System
Alternator24 volt, 250 amp24 volt, 250 amp
Lighting24 volt24 volt
Cranking MotorsTwo/24 voltTwo/24 volt
Suspension System
Front303 mm 11.92"303 mm 11.92"
Rear239 mm 9.40"239 mm 9.40"
Body
Capacity Struck240.7 yd3184 m3
Heaped (2:1, Sae)327 yd3250 m3
Payload814407.4 lb369409 kg
StructureFlat floor configurationFlat floor configuration
Weight92001.2 lb41731 kg
Canopy Sheet06mm 0.24" 690 Mpa 1,00,000 psi tensile strength steel06mm 0.24" 690 Mpa 1,00,000 psi tensile strength steel
Front Sheet10 mm 0.39" Outer, 12mm 0.47" Center, 1379 mPa 200,000 psi tensile strength steel10 mm 0.39" Outer, 12mm 0.47" Center, 1379 mPa 200,000 psi tensile strength steel
Side Sheet10 mm 0.39" 1379 Mpa 2,00,000 psi tensile strength steel10 mm 0.39" 1379 Mpa 2,00,000 psi tensile strength steel
Floor Sheet16 mm 0.63" Outer, 19mm 0.75" Center, 1379 mPa 200,000 psi tensile strength steel16 mm 0.63" Outer, 19mm 0.75" Center, 1379 mPa 200,000 psi tensile strength steel
Loading Height23.5 ft7.2 m
Engine
Number Of Cylinders1818
Engine Make22382238
Engine ModelSSDA18V170SSDA18V170
Power Measured @1900 rpm1900 rpm
Displacement4759.9 cu in78 L
Fuel TypeDieselDiesel
Horse Power: Sae J19953500.1 hp2610 kw
Horse Power: Iso 9249 / Sae J13493345.9 hp2495 kw
Operating Cycle4-cycle4-cycle
Weight (Wet)25904.4 lb11750 kg
Weight (Dry)24802.1 lb11250 kg
Driveline
Service Brake TypeOil-cooled, hydraulic-actuated, multiple disc brakes at each wheel.Oil-cooled, hydraulic-actuated, multiple disc brakes at each wheel.
Parking Brake TypeMultiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade at maximum gross vehicle weight.Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade at maximum gross vehicle weight.
Emergency BrakesOil-cooled, multiple disc front & rearAutomatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.Oil-cooled, multiple disc front & rearAutomatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
Wheel Brake LocksSwitch-activatedSwitch-activated
Electric Dynamic Retarder (Max.)Continuous at 4476 kW 6,000 hpContinuous at 4476 kW 6,000 hp
Max. Service Apply Pressure (Kpa)2750 psi18960 kPa
Total Friction Area Per Brake (Cm2)103729103729
Capacities
Fuel Tank1400.2 gal5300 L
Cooling System190 gal719 L
Hydraulic System350.1 gal1325 L
Crankcase90.1 gal341 L
Motor Gear Box25.1 gal95 L
Weights
Gross Weight1378499.8 lb625277 kg
Empty Weight564092.4 lb255868 kg
Weight Distribution Front - Empty48 %48 %
Weight Distribution Rear - Empty52 %52 %
Weight Distribution Front - Loaded33 %33 %
Weight Distribution Rear - Loaded67 %67 %
Tires
Standard Tire59/80 R6359/80 R63
Hydraulic System
Hoist CylinderTwo 2-stage dual-acting outbound cylinders and internal cushion valve, over-centre dampingTwo 2-stage dual-acting outbound cylinders and internal cushion valve, over-centre damping
Relief PressureHoist and brake cooling- 17237 kPa 2,500 psi Steering and brake-20685 kPa 3,000 psiHoist and brake cooling- 17237 kPa 2,500 psi Steering and brake-20685 kPa 3,000 psi
Hoist TimePower-up loaded: 21 sec; Power-down: 16 sec; Float-down empty:17 secPower-up loaded: 21 sec; Power-down: 16 sec; Float-down empty:17 sec
Turning Circle Diameter (Sae)105 ft32.1 m
Reservoir250 gal946.4 L
FiltrationIn-line replaceable elementsIn-line replaceable elements
SuctionSingle, full flow, 100 meshSingle, full flow, 100 mesh
Hoist And SteeringDual, in-line, high pressureDual, in-line, high pressure
PumpsTwo pumps, single package, end of alternatorTwo pumps, single package, end of alternator
Need the machine, not just the numbers?
Find one, value one, or tell the market what you need.
Manufacturer-published specifications.